中文版
English
Copyright © 2003-2019 Shanghai Shenke Dynamic Balancing Machine Manufacturing Co., Ltd All Rights Reserved 沪ICP备16012006号-4
24-hour service telephone：13585855377
搜索
Detailed introduction of dynamic balancing machine with simple operation
- Categories:news
- Author:
- Origin:
- Time of issue:2021-03-01 17:02
- Views:
Detailed introduction of dynamic balancing machine with simple operation
The on-site dynamic balance proofreading construction technology of dynamic balancing machine has been widely used in modern industrial production. If the balance is not good, it will accelerate the wear of the bearing, shorten the life of the machine, and cause destructive accidents in severe cases. This is a simple proofreading method for dynamic balancing devices. The common method of dynamic balance proofreading: In actual use, to make the remaining imbalance meet the requirements, it often has to go through repeated tests and corrections.
According to the technical requirements of drilling, it is generally not a method of drilling, but has been allocated to multiple holes in azimuth, select a number of azimuths to eliminate weight, and achieve the effect of balance and proofreading through vector synthesis. In order to install the counterweight conveniently, a few evenly distributed screw holes can be drilled on the balance rotor. According to the number of screw holes drilled by the balance rotor, there are generally three-point balance weight method and four-point balance weight method.
Generally speaking, the orientation is arbitrary, but our proofreading work is carried out after the dynamic balance test. Therefore, in the dynamic balance test, we usually choose the orientation of the phase detector. The balance component method is mainly used for single-sided and low-speed dynamic balancing. This method has a long downtime, does not require a phase sensor during measurement, and the test system is low in cost. All balancing procedures are carried out on the use of purely mechanical balancing equipment.
In the past dynamic balance calibration of rotating workpieces, manual operations were generally performed to complete the heavy calibration work, which was not only time-consuming and labor-intensive, but also might cause unnecessary loss or injury due to the operator's neglect of the amount in a special environment. Active positioning dynamic balancing machine breaks the traditional dynamic balancing machine with poor measuring accuracy, long measuring time and messy operation.
- Categories:news
- Author:
- Origin:
- Time of issue:2021-03-01 17:02
- Views:
The on-site dynamic balance proofreading construction technology of dynamic balancing machine has been widely used in modern industrial production. If the balance is not good, it will accelerate the wear of the bearing, shorten the life of the machine, and cause destructive accidents in severe cases. This is a simple proofreading method for dynamic balancing devices. The common method of dynamic balance proofreading: In actual use, to make the remaining imbalance meet the requirements, it often has to go through repeated tests and corrections.
According to the technical requirements of drilling, it is generally not a method of drilling, but has been allocated to multiple holes in azimuth, select a number of azimuths to eliminate weight, and achieve the effect of balance and proofreading through vector synthesis. In order to install the counterweight conveniently, a few evenly distributed screw holes can be drilled on the balance rotor. According to the number of screw holes drilled by the balance rotor, there are generally three-point balance weight method and four-point balance weight method.
Generally speaking, the orientation is arbitrary, but our proofreading work is carried out after the dynamic balance test. Therefore, in the dynamic balance test, we usually choose the orientation of the phase detector. The balance component method is mainly used for single-sided and low-speed dynamic balancing. This method has a long downtime, does not require a phase sensor during measurement, and the test system is low in cost. All balancing procedures are carried out on the use of purely mechanical balancing equipment.
In the past dynamic balance calibration of rotating workpieces, manual operations were generally performed to complete the heavy calibration work, which was not only time-consuming and labor-intensive, but also might cause unnecessary loss or injury due to the operator's neglect of the amount in a special environment. Active positioning dynamic balancing machine breaks the traditional dynamic balancing machine with poor measuring accuracy, long measuring time and messy operation.
